HomeProducts & ServicesImage GalleriesOnline ServicesFriends of BeamContact

 
Products & Services » Rust Proofing » Eco-Coat Salt & Offshore Spec 13


Eco-Coat Coastal, Salt Mining & Offshore Spec 13

(Order Code:- ES13)

Beam Eco-Coat Salt and Offshore Spec 13 is our most thorough and durable anti-corrosion treatment available and is designed for highly corrosive conditions typically found in salt and fertiliser works, coastal and offshore mining and shipping facilities.. Eco-Coat Spec 13 includes impact resistant underbody coatings, and clearcoat protection of the entire external painted surfaces of the vehicle Cab. The Eco-Coat range represents leading edge anti-corrosion technology designed to be long-lasting and highly durable.

Below is a guide to a typical Application. ( Note: This may vary depending upon vehicle type )

Application Guide:

Beam ML602 upper body rust treatmentt which is a highly advanced heavy duty corrosion inhibitive wax is applied to:
  • Inside Door cavities, Pillars, Rocker Panels and Box Sections.
  • Behind headlight and grille areas
  • Inside Bonnet & Boot lid stiffeners, tailgate areas.
  • Inside Chassis rails
  • Inside Plenum Chamber.
Eco-Coat Impact Resistant Polyurethane Coating is typically applied to:
  • The complete under body and chassis
  • Lower cavities of the front and rear guards.
  • Wheel arches, fuel, air and hydraulic tanks
  • Fixing points for tow bars, bull bars and side steps.
Ultratect "DUCOR" 2K High Build Epoxy Mastic coating is typically spray applied to:
  • Engine Sump, Transfer casing, Drive Line,Axles and differentials.
  • Suspension components, brake housings and steering arms.
  • Internal Foot wells and floor.
Ultratect “DURON" 2K Teflon/Polyurethane Clearcoat is typically spray applied to:
  • Underside of bonnet
  • Painted areas of the engine compartment.
  • Alloy engine components.
Metal Fix 1000 Product which is a high temperature rust resistant etch primer is applied to:
  • Entire Exhaust System
Denso Tape which is a corrosion resistant wax tape is hand wrapped around the following components.
  • Front suspension rod threads, bolts, tie rods ends and top shock absorber threads.
  • Brake adjusters, line fittings, pivots.
  • All accessible hydraulic fittings and joins.
  • All external electrical wiring connections.
Ultratect "DURON" 2K Teflon/Polyurethane Clearcoat is applied to the entire exterior painted surface of the vehicle cab to a minimum 70µm DFT provide long-term protection against attack by water, acids and most chemicals. Ultratect "DURON" is clear, UV stable (will not go yellow) and will not significantly change the appearance of the substrate. It can also be removed or repaired easily at any time if required.

The vehicle is then finished by replacing all parts that were removed prior to the vehicle being protected. All drain holes are checked to ensure they are free from any residual rustproofing product. The vehicle is then cleaned off using a mild solvent to ensure that there is no over-spray on the body, trim, windows or any other exterior parts. 
 

Recommended Additional Treatments

  • Rhino Lining Polyurethane spray-on tray and surface coating -  Ideal for load areas and to encapsulate and permanently protect high wear areas such as bull bars, side steps, internal floor pans etc....... Can be sprayed on up to 6mm thick, is slip resistant, prevents rust and corrosion, is waterproof and chemical resistant.

  

Application Time : (9 DAYS)

(Note: The above specification was last revised 1/10/2011 and should be used as a guide only. Some procedures may be altered or omitted for specific vehicle types or due to special customer requests. Beam reserves the right to alter this specification at any time without notice if new products or techniques become available.)



Downloads

Beam is proud to be 100% Australian owned and operated Site Map | Privacy Statement | Quality Statement
Beam are proudly affiliated with